KEXING Hardware Products Factory
0758-857749213929897956qiangfawj@163.com
Why is titanium alloy a difficult material to work?
发表时间:2018-07-25     阅读次数:     字体:【

Why do we think titanium alloy is a difficult material to work? Because of the lack of deep understanding of its processing mechanism and phenomenon.

1. Physical phenomena of titanium processing

The cutting force of titanium alloy processing is only slightly higher than that of steel with the same hardness, but the physical phenomenon of processing titanium alloy is much more complex than that of steel, which makes the processing of titanium alloy facing great difficulties.

Most titanium alloys have very low thermal conductivity, only 1/7 of that of steel and 1/16 of that of aluminum. Therefore, in the process of cutting of titanium alloy heat will not quickly passed to the artifact or taken away by chip, and agglomeration in cutting area, the temperature can be as high as 1 000 ℃ above, make the cutter blade quickly wear, cracks, and generate the devolop tumor, rapid wear of the blade, and make the cutting area produces more heat and further shorten the life of cutting tools.

The high temperature during cutting also destroys the surface integrity of titanium alloy parts, which leads to the decrease of geometric precision and the work hardening phenomenon which seriously reduces the fatigue strength.

The elasticity of titanium alloys may be beneficial to the performance of the parts, but the elastic deformation of the workpiece is an important cause of vibration during cutting. Cutting pressure makes the "elastic" workpiece leave the tool and rebound, so that the friction phenomenon between the tool and the workpiece is greater than the cutting action. Heat is also generated in the friction process, which aggravates the poor thermal conductivity of titanium alloy.

This problem is more serious when machining thin-walled or annular parts, which are easy to deform. It is not easy to machining thin-walled titanium alloy parts to the desired dimensional accuracy. Because when the workpiece material is pushed by the tool, the local deformation of the thin wall has exceeded the elastic range and produced plastic deformation, and the material strength and hardness of the cutting point increased significantly. At this point, machining at the previously determined cutting speed becomes too high, further leading to sharp tool wear.

"Heat" is difficult to process titanium alloy "culprit"!

2. Technical know-how for processing titanium alloys

On the basis of understanding the processing mechanism of titanium alloy, plus previous experience, the main processing techniques of titanium alloy are as follows:

(1) the use of positive Angle geometric shape of the blade, to reduce the cutting force, cutting heat and workpiece deformation.

(2) keep a constant feed to avoid hardening of the workpiece, in the cutting process, the tool should always be in the feed state, when milling radial cutting A E should be 30% of the radius.

(3) the use of high pressure and large flow cutting fluid, in order to ensure the thermal stability of the processing process, to prevent the workpiece surface denaturation and tool damage caused by high temperature.

(4) keep the blade edge sharp, blunt tool is the cause of heat accumulation and wear, easy to lead to tool failure.

(5) Machined in the softest state of titanium alloy as far as possible, because the material becomes more difficult to process after hardening, and heat treatment improves the strength of the material and increases the wear of the blade.

(6) Use a large tip arc radius or chamfer cutting to put as many edges into the cutting as possible. This reduces cutting force and heat at each point and prevents local breakage. In the milling process of titanium alloy, the cutting speed has the greatest influence on the tool life VC, and the radial cutting depth (milling depth) AE is the second.

3. Solve the titanium processing problem from the blade

The blade grooves wear in titanium alloy processing is the local wear in the back and front along the cutting depth direction, which is often caused by the hardening layer left by the previous processing. The chemical reaction and diffusion between the tool and the workpiece material in the processing temperature over 800℃ is also one of the reasons for the formation of groove wear. Because in the process of processing, the titanium molecules of the workpiece in front of the blade accumulation, under high pressure and high temperature "welding" to the blade, the formation of the accumulation of debris tumor. Special blade materials and geometry are required for titanium machining because the carbide coating of the blade is removed when the chip is removed from the blade.

4 suitable for titanium processing tool structure

The focus of titanium alloy processing is heat, a large amount of high pressure cutting fluid to timely and accurate injection to the cutting edge, to be able to quickly remove heat. There are special milling cutters on the market for titanium alloy processing unique structure.

 
上一篇:没有了
下一篇:The five points should be paid attention to in the use of aluminum alloy die casting molds
  • Kexing Hardware Products Factory      备案号:粤ICP备2021005799号  Address:Jinsheng Industrial Park, Jinli Town, Zhaoqing City, Guangdong Province, China  
  • Phone:0758-8577492    Email :qiangfawj@163.com    WebUrl:www.qiangfawujin.com网站地图
  • Copyright © 2018- Kexing Hardware Products Factory   All Rights Reserved.